Table of contents:
2024 Author: Sierra Becker | [email protected]. Last modified: 2024-02-26 03:46
Very often, young parents and not only have the question of how to make turntables from plastic bottles. This may be due to the desire to create a beautiful toy for your child or to decorate the playground where he plays. Gardeners also pay attention to such crafts. With the help of such simple devices, gardeners and vegetable growers are struggling with a very serious pest - cabbage. The solution is quite simple. A turntable is installed on the plot, which makes noise. It is this sound background that repels such pests according to popular beliefs. So the question of how to make turntables from plastic bottles is not so rare.
What do you need?
First you need to prepare all the tools and materials that you may need in the process. Materials Needed:
- plastic packaging;
- shrink;
- duct tape;
- paint;
- wire;
- plastic spacers for fixation.
Also do-it-yourself spinnermade using a specific set of tools. You need:
- scissors;
- marker;
- ruler;
- pattern;
- awl;
- knife.
It is better to prepare all this in advance, so that later in the process of creation there will be no unpleasant surprises.
Toy or playground decoration
At the initial stage, we make a wire support. To do this, bend it in the form of the letter "G". In this case, the upper part should be very short. In the place of the bend we put a fluoroplastic gasket. It must be securely fixed. If it scrolls, then you can wrap the wire with electrical tape and put a retainer on top of it. The lower part of the rack is wrapped with electrical tape. If desired, it can be replaced with heat shrink, which is then heated with a lighter. In this case, the length of this section should be limited by a fluoroplastic gasket. Then we take a plastic container. Containers with a volume of 0.5 or 1.0 liters are best suited. We cut it in half. Next, we make the markup using a marker and a pattern. We cut out the blades and wrap them in one direction and at a certain angle. Next, remove the cover. We make a hole in it of such a diameter that the wire can easily pass through and return it to its place. In the next step, this pinwheel needs to be properly styled with paint, which then needs to dry. Then this propeller is put on the wire and finally fixed with a second fluoroplastic gasket. To exclude possible injuries, the end of the rack is tightly wrapped with electrical tape. This is the most simple turntablemade from a bottle.
Protection of the infield
The previously described design of the propeller made of plastic containers is not applicable in the garden. For these purposes, a modified turntable is used, which has a greater degree of stability. It is made in the following way. Two holes are made in the container - in the lid and in the bottom, strictly one opposite the other. Then the blades are marked, which are then cut out of it with the help of knives and scissors and bent to the required angle. Then this container is put on the middle of the wire, fixed on each side with fluoroplastic gaskets. Then the wire is bent in the form of the letter "P". A greater degree of stability is provided by two legs instead of one. This way of making spinners out of plastic bottles is much more difficult and less commonly used.
CV
There is nothing super complicated in the manufacturing process of such propellers. Even a novice master can cope with this task without problems. Two ways are given on how to make turntables from plastic bottles. One of them is simpler and most often seen as a playground decoration. But the second one is a little more complicated and it is recommended to use it on a personal plot to protect against pests.
Recommended:
How to make a cat out of beads in different ways
Before you make a beaded cat, you need to decide what type of decoration you want to make. Volumetric or non-volumetric? What will it be - a brooch or embroidery? Work with beads, depending on the technique of its implementation, has its own nuances
Some tips on how to make a peacock out of plastic bottles
Plastic bottles - this is, perhaps, what can be found in the house of every person. We are constantly buying various drinks in plastic bottles. And after emptying them, we throw them away, without even thinking that this is an excellent material for creating various crafts
How to make a saber out of paper in different ways
In the article, we will look at how to make a saber out of paper in different ways. For decorative purposes, the blade can be rolled up from several layers of thin A4 paper using the origami technique. More durable will be a saber cut from corrugated packaging cardboard
How to make a palm tree out of plastic bottles for home decoration
The article shows how you can use waste plastic bottles to make an original palm tree
Let's talk about how to make a flower out of plastic bottles
Do-it-yourself products made from plastic bottles decorate many dwellings, summer cottages and garden plots. The thing is that plastic is inexpensive, it is constantly in wide availability, and most importantly, real masterpieces of arts and crafts are obtained from it. In this article we will talk about how you can make chic flowers from plastic bottles