Table of contents:

Shambhala bracelet. Weaving a classic and double bracelet
Shambhala bracelet. Weaving a classic and double bracelet
Anonim

All girls love jewelry, and this is understandable, because they, being the fair sex, know how to appreciate beauty. The most popular bracelet today is Shambhala. Weaving such a bracelet should not cause any particular difficulties even for beginners. And let someone perceive this jewelry as a talisman that brings good luck, but for someone it's just a beautiful bauble, one way or another, but this accessory is in trend today. The bracelet can be purchased at jewelry stores, but it will be much cheaper to make it yourself, this will allow you to get several stylish baubles for the same amount.

shambhala weaving
shambhala weaving

Materials for the bracelet

So, how to create a Shamballa bracelet? Weaving this little thing will not take much time, and for work you will need a waxed or leather cord, beautiful beads and a small weaving board. If there is none, then it is easy to make it by picking up a suitable piece of wood and hammering a small carnation on one side. An alternative to this device can be a small pillow and a regulara pin with which the cord will be attached for ease of use. You can also use ordinary tape - in this case, the weaving can be glued directly to the table.

Usually, the cord is taken in black, although this is not necessary. But the choice of beads should be given special attention, because they will set the style of jewelry, and its attractiveness depends on them.

Simple bracelet

How does work on the Shambhala bracelet begin? Weaving begins by measuring the wrist and cutting off the main thread twice as much as this measurement. Two working cords are made three times longer so that they are enough for all the weaves. After all the segments are tied in one knot, leaving about 4 cm of the free edge of the base.

weaving a double shamballa bracelet
weaving a double shamballa bracelet

Start work by tying a short cord with macrame loops either to the left or to the right, creating the so-called "square knot".

Shamballa bracelet weaving pattern
Shamballa bracelet weaving pattern

Continue this knitting until the turn of the bead comes, which is strung on the base, brought close to the weave and fastened with a square knot.

Shamballa bracelet weaving pattern
Shamballa bracelet weaving pattern

Next comes the turn of the next bead.

After the desired length is ready, the working ropes are cut and fixed with superglue. Next, you need to form a clasp for the Shamballa bracelet, which is also woven with square knots, only now they tie the two free ends of the base, folded in the opposite direction so that the work closes in a circle. Final step -attaching small acrylic beads to the ends of cords.

shambhala weaving
shambhala weaving

Double bracelet

The weaving of a double Shamballa bracelet is somewhat different from a simple one. Firstly, to create such an ornament, you will need more beads and a cord, and secondly, the knots in such a bracelet are slightly different from the simple version. Before starting work, a special pattern for weaving a Shamballa bracelet is created - this is especially important if any pattern is planned from the beads.

double shamballa bracelet
double shamballa bracelet

Work begins by cutting 3 cords: one 1.5 meters and two half a meter. The bases are tied and fastened for work. Next, 12 beads are strung on each of them and, having pulled the cords, they are fastened on the second side. The next step is knitting knots from the working thread, which is produced around two warps over the beads. The working thread is fastened and woven with 4 square knots. Then they begin to braid the beads with one of the working cords, passing it under the bracelet according to the spiral principle, winding it between the beads. The second working thread is twisted in the same way, only it is carried out over the work. The final stage is 4 square knots and the formation of a fastener.

Recommended: