Do-it-yourself pattern of a lantern sleeve

2024 Author: Sierra Becker | [email protected]. Last modified: 2024-02-26 03:46

On the question of what outfit is the most favorite among women, almost everyone will answer unequivocally: “Dress!” The history of its appearance in the wardrobe is rooted in the beginning of the emergence of human communities. Style, cut, decoration are constantly changing from one century to another. One thing is invariable in this amazing outfit - it always emphasizes female beauty, grace and makes a woman even more tender and irresistible. Each dress is beautiful in its own way, but it is especially elegant if the sleeve is cut with a “lantern”, that is, it is somewhat gathered or draped along the shoulder line or on the cuff. Any woman can make a puff sleeve pattern. You just need to take the basis of the drawing and simulate the assembly.

Making lantern sleeve pattern

If a decision is made to sew a romantic dress, then in most cases it is planned to assemble on the sleeve. The pattern of a dress with a "flashlight" sleeve is very easy if there is a basis for the drawing. There are several types of this dress. Lantern sleeves may be different. Assembly can be done by round andbottom. To obtain this type, you will need to take a drawing of a short sleeve pattern. Draw three vertical lines on it, where one should be in the center (that is, along the elbow bend), and the second two should be on the sides (one along the shoulder incision, and the other on the other side), and it is important that the distance between them is the same. Then the drawing along these lines is cut and moved apart to the required width (this will depend on the intended assembly).

Assembly at the bottom of the sleeve

Again, you will need the base of a dress or shirt. A blouse pattern with a “flashlight” sleeve is built according to the above method. Only in this case, the assembly will be mainly along the bottom and, possibly, slightly - along the rim. Three lines are also applied: along the elbow bend, along the shoulder incision. Only in this case, it will be necessary to move the drawing apart only along the bottom. That is, we leave the upper points on the lines in their original position, and expand the lower ones to the desired width. The resulting pattern of a flashlight sleeve will only have to be circled on paper or fabric. The bottom of such a sleeve is usually processed from the bottom with a cuff.

Long lantern sleeve

Romantic blouses and dresses can be for any season. And if there is a basic pattern for the “flashlight” sleeve (long or short, it doesn’t matter), then it can always be modeled. Just take the base of the dress with long sleeves. And the assembly can be outlined both along the edge and along the bottom, and quite possibly in two places at the same time. It depends on the desire of the woman. The principle of modeling is the same as in the first twocases. Three lines are outlined and drawn, and then, depending on the placement of the assembly, they are moved apart in the drawing.

Fancy sleeves

In the world of fashion, nothing is created. The same flashlight sleeve today can be seen not just gathered in the usual way, but with folds. This is a somewhat complex model, but you can master it if you wish. The pattern of the sleeve-lantern can be made exquisite. The basis of the drawing is taken. It is necessary to immediately determine the length, draw a line and cut off the excess. Then future folds are outlined. From the point of the elbow bend (that is, the center), you need to mark two more points at the same distance in both directions. Further from the elbow point, draw a line down (this line will not be cut, it is needed to build folds). Then draw lines from each upper marked point in an oblique direction to the center. The pattern should resemble parquet. That is, two triangles should be outlined in the drawing. From the acute angle of the upper triangle, a line is drawn to the lower triangle. The outlined lines are cut and moved apart to the desired width. Outline the drawing.

Other types of flare sleeves

Fantasy and imagination is the main principle of every fashion designer. Dressy sleeves can be made in various ways. You can only assemble in the center of the shoulder crease. Instead of assembling, you can make several folds there. Based on the drawing, you will need to draw two lines: horizontal and vertical. The vertical line is drawn from the shoulder fold, and the horizontal line is drawn along the linesarmpits. These lines are cut. The drawing should have two triangles. Now you need to move them apart in different directions, but do not take them away from the armpit points. The point on the shoulder bend will move apart, and the triangles will rise from the horizontal line. Such a sleeve is called "with a raised head." There will be an assembly on the collar, and the bottom can simply be folded or processed with a facing or cuff.

Thus, we can conclude that you can make a lantern sleeve pattern yourself, and if you have a basic drawing at hand, then, having shown imagination and ingenuity, you will get a unique outfit. You just need to remember the familiar advice from tailors that you need to measure seven times and cut off once. Thinking over the model of a flashlight sleeve, you should first of all carefully calculate everything on paper, and only then cut it out on fabric.