How to weave a rubber band bracelet on a loom? From the simplest to the most complex

2024 Author: Sierra Becker | [email protected]. Last modified: 2024-02-26 03:46

Small rubber bands are increasingly becoming the basis for all kinds of jewelry. It is easy to master different techniques. It is enough to understand the basic techniques - and soon it will be possible to independently explain to a beginner how to weave a bracelet from rubber bands on a loom or without it.

The simplest bracelet on two pegs of the loom

It can be a big machine, but you only need to use its two pegs, or a special small one, which is called a "slingshot". This technology will be clear even to beginners. Because in order to weave a bracelet out of rubber bands on the loom, it is enough to remember the beginning of work and the basic principle.

The first rubber band should be twisted into a figure eight. Then it must be put on two adjacent pegs of the machine. In the place where it twists, hook the S-shaped fastener. This is the beginning.

Continuation of how to weave a rubber band bracelet on a loom is as follows:

• put the second rubber band on top of the first, but it no longer needs to be twisted;
• remove the lower rubber band from the left andright pegs;
• repeat the first two steps so many times to get a chain of the desired length;
• throw the last loop on one peg;
• hook them with the clasp that was used at the beginning.

French braid bracelet weaving on two loom pegs

Its production is similar to what was described for the previous version. It is somewhat more complicated, but still, how to weave a rubber band bracelet on a loom should not be very difficult for beginners.

The beginning of weaving is the same. Then all the rubber bands are attached without twisting. In how to remove them from the pegs, and the differences begin:

• put on two rubber bands;
• remove bottom band from both pegs;
• put on another rubber band;
• remove the lower elastic from the left, and the middle one from the right;
• put on an elastic band;
• remove the middle one from the left peg, and the lower one from the right one;
• repeat 3-6 steps until the bracelet is the desired length;
• remove the bottom rubber bands from both pegs;
• throw the rubber band over one peg;
• secure the clasp by locking the bracelet into a ring.

It looks very impressive if you use rubber bands in two or three colors. At the same time, alternate them in strict order.

Pavement Bracelet

He is again weaving on two pegs of one loom. Only the volume and thickness increase due tousing double rubber bands. Working on it is similar to the previous two. But, as usual, there will be a difference. The beginning of how to weave a rubber band bracelet on a loom is the same. You only need to roll the figure eight with two rubber bands.

The technology of making a bracelet is as follows:

• put on two rubber bands of a different color;
• remove the bottom two from the right peg;
• put on two new rubber bands;
• remove the bottom four from the left;
• repeat the third action;
• from the right, remove the bottom four;
• repeat 3-6 points until you get a bracelet of the required length.

Close it into a ring according to the same principle as indicated for the two previous types of bracelets. You can already show off in front of your friends. Decorations on the handles will suffice.

Square Zigzag Bracelet

To weave it, you will need the entire loom. Its rows should be fixed in the same way to make a rectangle and all the pegs were on top of each other.

Before weaving a rubber band bracelet on the loom, it must be positioned so that the round part of the pegs looks at the needlewoman. The order of the rubber bands should not be violated. Otherwise, the bracelet will fall apart at the very last stage.

• Connect the first two pegs along the central row.
• The second rubber band should connect the two lower pegs of the loom on the left.
• Then on the left row the first two.
• Close the square with a rubber band.
• Repeat all actions, but only on the rightside, starting the square from the upper right corner of the existing square.
• Then again the square on the left. And so on until the end of the machine.
• Put a double-twisted rubber band on the last used peg.

Turn the machine over so that its pegs look at the needlewoman with recesses. Now you need a hook, which will need to remove all the rubber bands in reverse order. Moreover, you need to go along the three outer sides of the square, and then remove the rubber band, which is located in the central row.

Put a clasp on all the rubber bands of the last peg. Carefully remove the bracelet from the machine. It may turn out that it will not be long enough for the girl's wrist. Then, at the end free from the fastener, you need to weave a chain. Then close it in a ring.

Star bracelet

For him, the central row will need to be moved down. Place the machine as in the previous case. Now you can figure out how to weave a bracelet from elastic bands on a loom. The schemes for this start by going around the machine around the perimeter.

First from the central lower peg to the left and to the end of the loom, leaving the last one free, and to the last peg in the center row. Then the same on the right side of the machine. Lower all rubber bands from the top of the peg. This will be required for convenience in future work.

On the three central pegs and four on the sides, make the first star. To do this, put rubber bands on the central one and each in a circle. You need to start with a pair of second pegs of the centraland right rows.

Make such sprockets on the whole machine. They must be in contact with each other. Now you need to take the rubber band twisted in half and put it on the last central peg. The same action must be done for each center of the stars.

Turn the machine over. Start weaving the bracelet. First remove the rubber band from the center peg. Then move counterclockwise and remove everything only for the first star. Then do the same with the rubber bands of the second star and so on.

Now it's the perimeter's turn. It also needs to be weaved. Start with the bottom two, going from the center peg to the left and right. Then walk along the sides and finish with the upper ones directed towards the central one. Through all the loops on the last peg, stretch the rubber band and fasten the clasp on it. The bracelet can be removed. If it is small, then do the same as indicated for the previous one.