Table of contents:

Building a bell skirt pattern
Building a bell skirt pattern
Anonim

The emergence of skirts is rooted in the deep past. It is believed that it was she who first appeared from clothes. In museums, you can see pictures of primitive people wearing a kind of loincloth made of fur. Skirts were worn by both men and women. Although today it is in some countries the national dress for men. Everyone has heard about the famous Scottish woman. Modern women have in their wardrobe a lot of skirts, and all of different styles. It can be business, classic, romantic, strict, but the most fashionable today is the bell skirt. She is lush and sits well on any female figure. Each hostess can make a pattern for a bell skirt. You only need a few minutes of free time.

bell skirt pattern
bell skirt pattern

Building a bell skirt pattern

There are several different ways to build a blueprint. This skirt hugs the waist and flares out at the bottom. The length can be absolutely any. To build a drawing, only two main measurements are needed - this is the waist circumference and length. Then you need to take a piece of paper, a pencil, andyou can build a pattern of a bell skirt. In order to make it clearer, for example, let's take the following measurements: From (waist circumference) - 60 cm, and Du (skirt length) - 70 cm. And now we need to calculate two radii to build a drawing. The first formula: P1 \u003d half From - 4 cm \u003d 60 / 2-4 \u003d 26. We got the first radius. It will be the waistline. Second formula: P2=Du+P1=70+26=96. So we got the second radius.

bell skirt pattern with pleats
bell skirt pattern with pleats

Building on paper

Now we need to mark the main point O in the upper left corner on a sheet of paper. We will draw circles from it. First, by the value of the first radius, and then by the value of the second. In the end, you should get a cone with a cut off sharp corner. You can cut out the bell skirt pattern and start cutting on the fabric.

Other ways to build a drawing

You can model such a skirt if you have a ready-made base at hand. It always has darts for the back and front. Here they are needed. To begin with, from the end of each tuck (and this is the point of an acute angle), you need to draw a vertical line in the drawing to the bottom. Then cut along these lines and close the darts. The result should be the following: the tucks will close, and empty triangles should form below them. Then you need to circle the resulting drawing. If desired, you can reduce or increase the length, it can be a bell skirt to the floor, the pattern can be redone very easily. It is only necessary to extend the bottom line.

building a bell skirt pattern
building a bell skirt pattern

Simulation bell skirt

When availablebasic drawing, you can make anything out of it in a matter of minutes. Such a skirt can be on a yoke, with flounces, with wedges, with frills, with pleats. The pleated bell skirt pattern is easy to make. If the drawing is built and the intended darts remain on it (from which vertical lines were drawn), then it will only be necessary to cut along this line again and push the two parts from the resulting drawing in different directions to the desired width. This is the future fold. Several such folds can be made. Only in this case it will be necessary to draw several vertical lines. It is not difficult to make such a skirt with a yoke. To do this, the future coquette should be noted on the finished drawing. On the side line from the top line of the drawing, go down 5 cm and put a point K1. On the fold line (center of the skirt), lower from the top line of the drawing by 8-10 cm and put a point K2. Then draw an oblique line along them, this will be a coquette. It remains only to cut and cut into fabric. You can easily make a pattern for a bell skirt, you just need to know the basic measurements or have a base drawing on hand.

floor-length bell skirt pattern
floor-length bell skirt pattern

Fancy skirts

Women's fantasy has no limits. And any woman can always create an outfit from any fabric. If there is a basic drawing, then the pattern of the bell skirt can also be made with wedges. There is nothing complicated here, you just need to draw another triangle to the main pattern. To build, you need two measurements, this is the height of the wedge and its width. Having measured the required height in the drawing (from the bottom of the skirt), put point B. Then the line fromthe bottom of the skirt and up to this point will need to be cut. And the wedge itself can be built right there on the drawing, or it can be done separately, that is, there will be one more detail. To build it, you need to draw a vertical line from point B1 down, it is equal to the height of the wedge, and put point B2. From point B2, draw a horizontal line to the right, the length of which is equal to the width of the wedge, and put B3. Further from point B1 again draw an oblique line to point B3. And make the bottom line a little semicircular. That's it, the wedge is ready.

Thus, it is very easy to build a bell skirt pattern. You just need to know your measurements, take a piece of paper, a pencil and scissors. The task can be simplified if there is a drawing of the base-skirt. Then it can be modeled even faster, and no additional mathematical calculations are required.

Wear this skirt with pleasure and be adorable!

Recommended: