Table of contents:

Master class on how to make a headband with stones and rhinestones
Master class on how to make a headband with stones and rhinestones
Anonim

The headband with stones and rhinestones can be used for a casual look, and perhaps for festive occasions. Do-it-yourself such an accessory is made quickly enough, and the material costs will be small. And you can be sure that no one will have such a decoration.

Headband for every day

headband with stones and rhinestones
headband with stones and rhinestones

Getting Started:

  1. Draw a 1 by 1 sketch of the headband brooch on paper.
  2. Place a piece of felt in front of you.
  3. Gently glue the first large stone in the center.
  4. Take a chain of small pebbles and glue one end close to the crystal on the felt. Put a few glue dots around the main stone. Glue the chain along the contour of the crystal to make a circle.
  5. Lay large rhinestones in front of you. Put a dot of glue over the resulting circle and glue the rhinestone with tweezers. In this way, make another circle.
  6. Glue three small rhinestones on the left side. Then attach a chain and a large pebble. Glue them on. Atyou should get two circles.
  7. Paste the pebble with the chain on the left side with small rhinestones.
  8. Make a similar circle with rhinestones on the right side.
  9. Circle three circles together along the contour with a chain of large pebbles.
  10. Glue a chain of small pebbles on top.
  11. Cut out the learned figure from rhinestones and pebbles along the contour.
  12. Glue the piece to the center of the elastic.
  13. Apply it to your head and measure the required length so that the brooch is slightly to the side. Cut off the excess.
  14. Sew or glue the ends of the elastic.

Such headbands with stones and rhinestones with your own hands will turn out more elegant if you use a ribbon instead of an elastic band. Then the ends do not need to be glued or sewn, they will be tied.

Simple but very beautiful hoop

headbands with stones and rhinestones with their own hands
headbands with stones and rhinestones with their own hands

To make this headband with stones and rhinestones, you will need a very strong glue. It is better to use a glue gun or Moment, as it will quickly and efficiently cope with the task. You also need a hoop frame. Thin metal would look best.

So, take the frame of the headband and degrease its surface using alcohol. Use a marker to mark the places where the straziki will begin and end. Lay out the stones and rhinestones in front of you in the order in which they should go on the rim. Start gluing the decor to the hoop. Do this carefully so that the glue does not peek anywhere, and the pebbles stick evenly.

Take decor,whose diameter is equal to or greater than the width of the rim. Then it will feel like the stones and rhinestones are attached directly to your hair.

Wedding headband with stones and rhinestones

headband with stones and rhinestones master class
headband with stones and rhinestones master class

Master class:

  1. Prepare the glue, rim and decor. You can use ready-made parts made of beads and pebbles, which will only have to be connected to each other. You can also make them yourself, starting from the first master class on creating a brooch.
  2. Assemble decorative pieces with beads and stones, then lay them out in front of you as you would like them to appear on the headband.
  3. Glue the decor together in the correct sequence, use a mesh or fabric as a substrate.
  4. Glue the finished decoration to the headband.

The festive headband is ready.

Use curly stones

headband with stones and rhinestones master class
headband with stones and rhinestones master class

Instructions on how to make a headband with figured stones:

  1. Take the frame of the metal rim, wire to match the color, round nose pliers, curly pebbles (flowers) and beads.
  2. Wrap a piece of wire and attach a pebble to one end. Thus decorate the bezel. Place the pebbles close to each other and direct the wire in different directions. Decorate at different heights.
  3. Fill the gaps on the rim with wire, to do this, wind it tightly.

The headband with stones and rhinestones is ready.

Recommended: