Table of contents:

Knitting socks with a toe: instructions and recommendations
Knitting socks with a toe: instructions and recommendations
Anonim

Knitting socks from the toe is considered an unusual way, because, as a rule, products are made starting with a cuff and ending with fingers. The advantages of this technique are that the toe is neat, the heel is knitted the other way around, but the appearance has a similar shape to the classic square heel.

Initial process in detail

knitting socks with a toe
knitting socks with a toe

Knitting socks with a toe requires 5 stocking needles, you will also need one extra to knit the heel. However, it's not that important. For the manufacture of a product of the 42nd size, 100 grams of thin wool mixture was spent per man. Knitting needles should be chosen thin, as knitting will differ in density.

How to create socks: master class

knitting a sock with a toe
knitting a sock with a toe

It is necessary to make a sample in advance and determine the density of the product. After holding an individual set of loops, the number of rows when creating a product. To start knitting socks from the toe, you should crochet a chain of 12 loops.

You can alsotake a knitting needle, throw a loop on it from the hook, insert the tip of the knitting needle into the half loops of the chain in turn. After you need to grab the thread and pull the loop onto the knitting needle. On each side of the chain, there should be 12 loops on the needle and from the back of the chain on the second knitting needle, you must also dial 12 loops. You can use the method of knitting socks with a toe on two knitting needles. More on him later.

The first row is knitted in a circle thanks to the facial loops, while the loops must be divided into 4 knitting needles of 6.

How to knit the toe of the product

knitting with toe with heel boomerang
knitting with toe with heel boomerang

From the second row, you need to start adding on the sides after the first loop of the first knitting needle, before the last on the second, after the first on the third and before the final loop on the fourth knitting needle. It is necessary to add loops from broaches, for this purpose, with the right knitting needle, you need to pick up the thread between the loops, throw it on the left knitting needle and knit it behind the far wall of the front. The loops should be added through the row, until the toe is equal to the width of the entire foot. For the men's product, 20 rows were knitted, and the number of loops on each knitting needle was increased to 16, in total there will be 64 on 4 knitting needles.

Main part of product

After you need to knit the product without additions, up to the instep of the foot. Next, a lifting wedge is created. Through the row, add on the sides after the first loop on the third needle and before the last loop on the fourth. After 16 rows on these knitting needles, the number of loops will increase to 24, a total of 16 has increased. On the third, as well as the fourth knitting needlethe sole of the product is made, and the sock is knitted from the toe with the heel. To create a heel, on the third and fourth knitting needles, divide the loops into three equal parts, 6 each, transfer them to a variety of knitting needles to make it comfortable to knit.

Creating a heel

knitting with a toe on two knitting needles
knitting with a toe on two knitting needles

Let's move on to the next step. Knitting socks with a toe with a boomerang heel is an easy technique. At the beginning of the process, you need to knit a pattern on the central 16 loops in reverse, as well as in straight rows. In this case, use the front surface. The first edge loop is always removed so that a chain border appears. For the heel, the number of rows corresponds to the number of loops on the needle (multiply by 2 or equals 32 rows).

Having done the last row of the section, you need to cast on the loops on the sides, the knitting needle should be inserted behind the edge loops, and, pulling out the loop, you should dial 16 more. and on the front side of the loop should be dialed as front. Having typed loops on one side, the heel must be knitted in the opposite direction. After the loops in the center, you should dial them on the second side of the side, also take 16 loops on the knitting needle.

After 48 loops of the heel are knitted in reverse or straight rows, the center must be tied, the first hem is removed without fail, and the last is knitted together with the loop on the side.

On the front side, two loops need to be knitted together with a front one with a broach, for this purpose, you need to reshoot the last loop of the heel on the right knitting needle, do notknitting after. The first one from the side needs to be knitted with the front one, after the left knitting needle you need to pick up the untied one and throw it over the second one. On the wrong side, a pair of loops is knitted together with one wrong side. In all rows, one loop will begin to decrease, then from one side, then from the other side. In total, 32 rows should be knitted so that there are only heel loops.

Creating a cuff

After making the heel, the sock with the toe is knitted with knitting needles (all four), you need to make eight decreases on the sides in all rows to narrow the ankle. After that, four rows should be knitted using the front surface, the cuff should be an elastic band 4x4 30 rows. To finish knitting socks from the toe, you should close the loops of the elastic band. Another sock is made according to a similar plan.

Production of a product on several knitting needles

knitting socks
knitting socks

Knitting socks from the toe thanks to open loops is as follows. The density of the process, for example, is 18 loops - this is equal to 10 cm. We will dial 20, 10 for each knitting needle. It is necessary to knit a circle, then add along the hem, at the beginning of the row and at the end. A further circle is created without additions, you need to knit a toe with an alternation of a circle with and without an addition until there are 18 loops each.

When all the loops are created, they need to be transferred to one knitting needle and continue the process, relying on the double hollow gum method. Next, just knit the length of the sock up to the heel. After we re-transfer the loops to the knitting needle and continue to take the height of the gum about 70 mm. Knitting ends with an elastic band 2x2. When closingloops they should be pulled out harder so that the elastic does not tighten, otherwise the product will be difficult to put on the leg.

Recommended: